NEPTUNE6-COM - Le pilote NEPTUNE6 logiciel de programmation

Drivers


Caractéristiques générales

NEPTUNE6-COM - NEPTUNE6-COM

Le logiciel NEPTUNE6-COM est utilisé pour définir les paramètres de fonctionnement et les configurations du pilote NEPTUNE6 sur un PC, de sorte que les données enregistrées peuvent être enregistrées sur le disque ou les données chargées sur le disque peuvent être envoyées. La programmation s’effectue via un PC avec le port série RS232.

Vous pouvez définir les données suivantes à l’aide du logiciel NEPTUNE6-COM:

  • Tableau de vérité qui lie l’état des entrées aux 2 sorties
  • Définir le mode de fonctionnement requis (mode Réglage/Réinitialisation et déclenchement)
  • Activer/désactiver le contrôle sur le courant de chargement
  • Définit les heures sur les sorties
  • Enregistrez les paramètres lus par NEPTUNE6 sur le disque
  • Envoyer les données chargées sur le disque sur NEPTUNE6
  • Testez les entrées et les sorties. Mesurez la température dans le conducteur

Avec la nouvelle version de logiciel pour le nouveau NEPTUNE6 avec firmware V2.0, vous pouvez activer/désactiver la fonction de fragmentation de la section adhésive.

Configuration minimale requise:

  • Système d’exploitation: WindowsTM 95, 98, ME, NT4, 2000, XP
  • Ordinateur: 100% WindowsTM compatible avec le port série RS232
  • CPU: 200 MHz ou supérieur

WindowsTM est une marque déposée appartenant à Microsoft Corporation

Exemples de programmes

Files included in the library:

FILE NAME CONFIGURATION DESCRIPTION
AND-OR.np6 Management of a system where the output is activated by the simultaneous presence of 2 signals sent from a piece validity control PLC (connected on IN1) and from a cam controller (connected in IN2). To test the output, there is a dedicated test input (IN3) that activates the output despite the status of the inputs IN1 and IN2.
AND-ORx2.np6 Management of the double enabling signal function to activate the output with a third input to test the outputs. IN1 and IN2 are set in AND to manage the double enabling signal (output O1 active if both active), while IN3 activates output O1 despite the status of IN1 and IN2 to test the system. The inputs IN4, IN5 and IN6 perform on O2 the same function as IN1-IN3 (IN4 and IN5 for the double enabling signal and IN6 for the test). Each time the output is activated, an over-boost pulse is generated first of 4msec, then the voltage settles at 24V until the condition that keeps the output active is eliminated.
auto_rpt.np6 Each output is associated with an activation input. Each time the input activates, the corresponding output generates an over-boost pulse of 4msec followed by a 24V pulse of 13msec. At the end of the time, the output switches back to pause to wait for a new pulse on the input. The timing of the output is constant even when the duration of the input pulse varies.
frenofrizione.np6 Management of an electro-magnetic brake/clutch unit. The brake is connected to -O (output 2), the clutch to O (output 1). IN1 is the start, IN2 is the stop, IN3 is the phase reading photocell and IN4 enables the photocell. An over-boost voltage of 100msec is applied on the brake/clutch.
hvevssr.np6 Typical pilot mode of driver boards with over-boost HVEVSSR.
monostx2.np6 Each output is associated with an activation input. Each time the input activates, the corresponding output generates an over-boost pulse of 4msec followed by a 24V pulse of 13msec. At the end of the time, the output switches back to pause to wait for a new pulse on the input. The timing of the output is constant even when the duration of the input pulse varies.
SetReset.np6 Demo of the Set/Reset function. IN1 is the Set input, which activates O and de-activates -O. If IN1 returns to 0 O remains activated until input IN2 (Reset) is activated, which not only de-activates O, but also activates -O. The reset condition too remains saved until input IN1 is activated again.
startstop.np6 Example of using the set/reset function. Input IN1 (Set or Start) activates output O1 and de-activates O2. The 2 outputs remain in this status until input IN2 (Reset or Stop) is activated, which de-activates O1 and activates O2. This second condition too remains saved until IN1 is activated. If an input is activated when the other input is still activated, this new condition is ignored and the outputs remain in the old condition.
timed and-or.np6 The piece presence photocell is connected to input IN1 that causes activation of output O1 for the time set in « Output 1 Voltage V2 ». Output O1 is bridged towards input IN2 and establishes the presence of the piece being conveyed. Input IN3 is on the other hand that related to the shoot phase signal. When IN2 and IN3 are simultaneously present, output O2, connected to the gun, activates for a time set in « Output 2 ».IN4 is the test input used to activate output O2 despite the status of the other inputs.

Foire aux questions

Produits connexes



Soumettre une demande: